Contents
Memory and variables

Memory: STO, RCL, Ans and what M+ keeps

Three kinds of memory do three different jobs. Learn which one your next calculation reads without asking, and how to store into A to F.

7 min read Beginner updated 2026-11-07

Most memory mistakes are not about forgetting a value but about assuming the wrong memory holds it. Ans changes the moment you press = again, a variable survives into the next question, and the M total quietly keeps adding lines you thought you had removed.

Ans: the memory you use by accident

Ans holds the last result you confirmed with =. It is used automatically when a new calculation starts with an operator, which is what makes it convenient and what makes it dangerous.

Watch Ans move

  1. 1
    2 5 × 4 =

    100. Ans is now 100.

  2. 2
    ÷ 5 =

    Starting with an operator puts Ans in front: Ans ÷ 5 gives 20.

  3. 3
    Ans × 2 =

    40, with Ans written on the line this time.

  • SHIFT + Ans is the % legend on the same key - a different function, and a common exam slip.
  • Ans is a memory that holds one value only. Anything you want to keep belongs in a variable.

Storing a value in a variable

The STO key assigns the value on the screen to a variable. On EX the SHIFT legend above the same key is RECALL, so one key does both directions.

Store 21 in A, then calculate past it

  1. 1
    3 × 7 =

    21 on the screen.

  2. 2
    STO

    The calculator asks which variable should receive the value.

  3. 3
    ALPHA (−)

    A. The A legend sits above the (−) key.

  4. 4
    2 1 − 5 =

    16. Ans is now 16, while A still holds 21.

  5. 5
    SHIFT STO

    RECALL opens the variable list.

  6. 6
    ▼ =

    Choose A: the display shows 21 again.

fx-991EX Plus 0.
STO, then the ALPHA legend of the variable: this pair stores the value on the screen in A. Rendered from the same layout data the online calculator uses — key positions and silkscreen labels are not stylised.
Example Two memories, one value

Input

3 × 7 = → STO A → 21 − 5 =

Result

Ans = 16, A = 21

That difference is the whole reason to store a value instead of reusing the previous line.

VariableALPHA legend onTypical use
A(−)a value a formula needs more than once
B°′″the second of two intermediate results
Cx⁻¹the third
Dsinspare
Ecosspare
Ftanspare
x)the unknown Solver and the function apps work on
yS⇔Dthe second variable of those apps
MM+the independent running total

M+ and the running total

M+ adds whatever is on the screen to the M memory; SHIFT + M+ is the M− legend on the same key and takes it back out. Because M does not depend on Ans, it is the right tool for a list of amounts.

Total 12.5 and 9.8, then remove a line keyed twice

  1. 1
    1 2 . 5 =

    12.5 on the screen.

  2. 2
    M+

    Add it to M.

  3. 3
    9 . 8 =

    9.8.

  4. 4
    M+ M+

    Keyed twice by mistake; M is now 32.1.

  5. 5
    SHIFT M+

    M− takes the shown 9.8 back out, leaving 22.3.

  6. 6
    ALPHA M+

    Put M into an expression to read the total: 22.3.

PreAns: check the key face

The key layout described in this manual puts only Ans on that key - there is no PreAns legend. Some regional ClassWiz models print PreAns above the same key, and there the ALPHA layer gives you the result before the last one. Look at your own key face rather than a photo from another market.

Which memory to use

MemoryUse it forWatch out
Ansthe step you have just doneevery = replaces it
A to Fa value a formula needs twiceit survives into your next question
x and ySolver and the function applicationsthose apps read them, so leftovers change results
Ma running totalit keeps adding until you subtract or clear it

Was this guide helpful?

Tell us what was unclear, missing or wrong. A concrete sentence is more useful than a rating.